SFX Filtration System Setup
Updated
PRELIMINARY STEPS
READ ALL INSTRUCTIONS CAREFULLY and get a thorough understanding of what is required to assemble your SFX series Filter Pump.
Before you begin to assemble the pool, identify, count, and check all parts needed for assembly.
It is recommended that you have some PETROLEUM JELLY on hand for lubricating the gaskets.
FILTER PUMP IMPORTANT NOTES
Installer shall follow written instructions provided for operation of the filter pump systems.
All electrical components shall be installed in accordance with Article 680 of the National Electrical Code (NEC) “Swimming Pools, Fountains and Similar Installations” or its latest approved edition.
The Type D Filter Cartridge 7 will hold as many as 2 of the 1” diameter chlorine tablets and the Type A/C Filter Cartridge 7 will hold as many as 6 of the 1” diameter chlorine tablets. Check your chlorine levels to determine the proper number of chlorine tablets to add. The filter cartridge will automatically dispense chlorine into the pool as the Filter Pump runs. You must have the type of Filter Cartridge 7 with a central core mesh divider (See page 8) to use the chlorine dispenser. DO NOT use this to dispense powdered chlorine, shock treatment or any other type of chemicals as damage to the pump, filter cartridge, and pool will occur.
The SFX Series Filter Pump systems are manufactured by Polygroup™ and ETL control number 4000608 and 4006317 - double insulated and grounded - 120 V.A.C. - 60 Hz. (ALL Units must have a minimum of 105 V.A.C. to start and run properly).
FILTER PUMP POWER INFORMATION
NOTE: Parts List number reference may vary fromprevious years owner's manual
THE FILTER CARTRIDGE WILL HOLD 1” DIAMETER CHLORINE TABLETS. CHECK YOUR CHLORINE LEVELS TO DETERMINE THE PROPER NUMBEROF TABLETS TO ADD.
Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.
WARNING: CLIMBING HAZARD! PLEASE PREVENT CHILDREN FROM CLIMBING ON THE FILTER CANISTER TO GAIN ACCESS TO THE POOL.
SETUP INSTRUCTIONS
Set up the pool by following all the instructions that come with the pool. Do not fill water until the Filter Pump is properly installed. Locate the Outlet and Inlet openings on the pool wall.
Install the Suction Fitting on the outlet opening of the pool.
Install the Return Fitting on the Inlet opening of the pool.
Remove the Filter Pump Assembly, Hoses, and Hose Clamps from the package.
Connect the Hose from the Suction Fitting to the Filter Pump Inlet.
Connect the Hose from the pool Return Fitting to the Filter Pump outlet.
Tighten all Hose Clamps to prevent water leakage.
Slip the Top Cover onto the skimmer canister.
Fill water to a proper level, plug in the GFCI, and enjoy clean pool water.
FILTER PUMP OPERATION
Plug the GFCI power cord to a properly grounded receptacle at least 15 feet (4.5m) away from the pool.
IMPORTANT: To start the filter pump, press the RESET button on the GFCI plug .
Check the return fitting on the inside of the pool for correct flow, it should feel like a solid stream of water returning to the pool.You can use the return flow as a gauge to determine when the filter needs cleaning or replacement. If you feel a reduction in flow, clean or replace filter.
Test water and adjust as needed, read Section 9 - “POOL WATER CARE”. VERY IMPORTANT - FILTER PUMP ALONE WILL NOT PREVENT ALGAE FROM GROWING IN POOL WATER; THIS CAN ONLY BE DONE BY MAINTAINING PROPERCHLORINE AND pH LEVELS AT ALL TIMES!
The filter cartridge may need to be cleaned and/or replaced several times at start up until the correct chlorine and pH levelsare attained. We recommend that you keep at least one spare filter cartridge on hand at all times. Filter cartridges may be purchased at the store you purchased your pool from, or ordered from Polygroup™.
To turn off the filter pump, unplug the GFCI power cord 2 6 .
PUMP MOTOR PROTECTION
IMPORTANT! Your filter pump is protected by a thermal switch. The switch senses the temperature of the filter pump. If it gets too hot, the switch willstop the pump from running until it cools off. It will automatically turn back on when the filter pump has cooled down. This is a safety device to preventpump damage and prolong service life. If your pump is automatically turning off, it is because of high pool water temperature and/or low water flowsthrough the pump. If this happens you need to check the water flow and correct it if needed, as this filter pump uses the water flow for cooling. Youmay also want to run the pump at night when the temperature is lower.
FILTER CARTRIDGE CLEANING & REPLACEMENT
First, unplug (turn off) the Pump. Then remove the Top Cover 5. Remove the Strainer Basket 24 and the Filter Cartridge 7.
Basic Cleaning: Clean the filter cartridge by thoroughly pressurewashing inside and out with a garden hose. Allow a few hours for the filter to fully dry and CAREFULLY BRUSH the pleats (to avoid wear out, do not scrub the pleated surface areas). Cleaning and scrubbing a filter too vigorously will also wear out the cartridge much faster than if it is simply hosed off correctly.
To remove tough oils (e.g. suntan, bodyoils, algae, etc) it is recommendedto soak cartridge in a 1lb trisodium phosphate solution (or any other strong detergent) to 5Ga water for up to 12hrs. Rinse cartridge to remove dirt. To remove algae, add 1/2 pint of pool chlorine or 1 pint of liquid household bleach to the cleaning solution, 1 hour before retrieving the cartridge. Thoroughly rinse before usage on filter case.
Excessive calcium and/or mineral deposits may build up on a filter cartridgeand should be handled differently. Contact your local pool supply store to ask about additional filter cartridge cleaners or treatment for calcium or mineral deposits. Check pool chemistry for high pH or alkalinity; this may cause a calcium or mineral build-up.
Re-assemble in reverse order.
A spare “stand-by” Filter Cartridge 7 is an excellent investment. It provides a convenient way to continue filtration of your pool while cleaning or replacing a dirtyFilter Cartridge 7. Also, a well-maintained, clean cartridge assures you that your filter will always be ready to operate at peak efficiency.
Filter cartridges may be purchased at the store you purchased your pool from, or ordered from Polygroup™. Always replace with genuine Polygroup™ SUMMERWAVES™ filter cartridges.
POOL MAINTENANCE
Check and adjust pH and chlorine levels daily using required chemicals. See Section “POOL WATER CARE”.
Check filter pump output daily. If flow is reduced, see Symptom 2 in Section “TROUBLE SHOOTING GUIDE”.
Check filter pump, hoses, fitting for leaks. If a leak is found, see Symptom 4 in Section “TROUBLE SHOOTING GUIDE”.
POOL WATER CARE
The following items are required and readily available from your local pool supply store:
TEST KIT - Used to check chlorine and pH levels.
1” CHLORINE TABLETS - Used to disinfect pool water and help control the growth of algae.
pH CONTROL CHEMICALS - Used to adjust pH levels Up (Soda Ash) or Down (Acid).
ALGAECIDES - Used to eliminate algae.
SUPERCHLORINATOR - Used to destroy combined chlorine, ammonia, nitrogen, and organic compounds.
LEAF NET with handle - Used to remove leaves, trash, insects, etc. from pool.
CHLORINE DISPENSER (Supplied with Polygroup™”s patented Filter Cartridge U.S. Pat. 7,005,062) - Used to dispense 1” chlorine tablets ONLY.
Use test kit daily to check pH and chlorine levels. Adjust accordingly using the required chemicals.
NOTE : Excessive levels of chlorine or low pH levels will damage pool liner.
The pool can be cleaned using a garden hose powered vacuum from Polygroup™ or a pool supply store.
Using a foot bath near the pool to wash off your feet prior to entering the pool will assist in keeping the pool clean.
Well water often presents special problems with water chemistry. If you must use well water, take a sample to your local pool chemical supplier for analysis beforeadding ANY chemicals
Refer to the POOL”s USER MANUEL for the capacity of your pool. You will need this information to determine the amount of chemicals you will need to correct thepool water. NOTE: It is recommended to use a 5 gallon bucket of water to mix and dissolve your chemicals and then applying directly to the pool water. Follow manufacturers label directions on all chemicals.*Most pool supply stores will test your pool water for free and advise you of what chemicals you need, and the correct amount to use for your pool. You will need to tell them the pool capacity in gallons.
IMPORTANT - We cannot over-stress the importance of proper and adequate daily chemical treatment. Chlorine and pH levels must be properly maintained at alltimes. PUMP AND FILTER ALONE WILL NOT PREVENT ALGAE FROM GROWING IN POOL WATER; THIS CAN ONLY BE DONE BY MAINTAINING PROPER CHLORINE AND pH LEVELS AT ALL TIMES.
Maintain pH level between 7.3 and 7.8.
Maintain chlorine level between 1.0 and 1.6 ppm (parts per million).
Superchlorinate your pool at least every other week.
NOTE :
Hot weather/heavy use may require pH and chlorine levels to be maintained on the upper side of the scale and superchlorination of the pool every week.
Using a pool cover and/or solar cover will assist in maintaining your pH and chlorine levels by reducing the amount of evaporation from your pool.
CAUTION - Concentrated chlorine levels and low pH levels will damage pool. You must follow the instructions for the pool chemicals you use, as to quantityand recommended usage. NEVER drop lumps or pellets of chemicals in pool; this may present a hazard to swimmers and/or damage your liner.
POOL PUMP DISASSEMBLY & STORAGE
First, unplug the main power cord of the system.
Remove the Top Cover 5 , Strainer Basket and Filter Cartridge 7 and remove any chlorine tablets left inside the core section of the filter.
Loosen all Hose Clamps . Remove the Return Hose and allow water to drain out.
Remove the Return Fitting - and clean the parts and lubricate Gasket with petroleum jelly and reassemble all parts then place them in a safe place.
Remove the Motor assembly 3 by turning the Motor Seal Nut 1 counter-clockwise. Now clean the pump, dry it off, and then lubricate the Motor Seal 4on the motor with petroleum jelly and place it in a safe place.
Please refer to illustration on next page to reassemble the motor.
Remove the Filter pump canister 9 from liner by turning the Skimmer Seal Ring counter-clockwise. Remove the Weir 8 and Strainer Basket . Clean allparts and dry them off. Then reassemble the filter cartridge, strainer basket, weir, top cover, etc. onto the canister. Place the assembled unit in a safe place.
MOTOR REPLACEMENT INSTRUCTION
IMPORTANT: The Preferred Method Is To Drain Enough Water From The Pool First Then Dismount The Entire Skimmer System Before Replacement. IfUser Prefer To Operate It On The Pool, Please Refer To Below Process. Please Note Incorrect Handling Method May Cause Water Leakage Between Canister and Liner
Insert the Water Stopper into the water intake of pump. Push the Stopper to make it engage with Skimmer Seal Ring closely.
Unplug the power.
Detach the Locking Ring and Diverter Fitting by anticlockwise turning. Insert the Return fitting plug (RF Plug) .
Remove Top Cover 5, Strainer Basket , Filter Cartridge 7, it isadvised to use a water container, such as a bucket shown with dotted line in the illustration to collect the purged water.
Remove the Motor Seal Nut 1 by turning according to the arrow direction.Do not pull or push the canister as you can to avoid engagement damage between canister and pool liner.
Remove Motor assembly 3 . Be careful not to lose the rubber nozzle 2 .
Check the Motor Seal 4 from bottom side to make sure it at the original slot correctly.Use left hand to hold the motor from Canister inside. Make sure the motor water outlet align with Canister outlet direction. Then use right hand to tighten the Motor Seal Nut 1 like the arrow direction (One more person help will be easier for replacement).
ROTOR REPLACEMENT INSTRUCTION
Disassemble the wall fitting and canister like item 7 POOL PUMP DISASSEMBLY AND STORAGE procedure.
Detach the motor assembly 3 from canister 9 by turning the counter-clockwise. Be careful not to lose the Motor Seal Gasket 2 .
Refer to below motor assembly illustration to replace the Rotor Assembly ,remove the Volute Cover and pull out the Rotor Assembly from the Stator. Insert new Rotor Assembly into the Stator .
Align the Shaft properly and fasten the Volute cover with the Volute Cover Lock Nut or with the Volute Cover Bolt and Nut Set .
Attach the Motor Seal 4 to the outlet of Motor Assembly.
Slowly insert the motor assembly back into the Canister 9 , so that the Motor Seal 4 is aligned with the outlet port of the Canister 9. Also please refer to themotor assembly process ”G” in 7 POWER FILTER DISASSEMBLY AND STORAGE.
Tighten the Motor Seal Nut 1 by turning the clockwise, be sure the Motor Seal 4 is properly in place.
